HAIR BODY 575 In our view, the concept of hair body, as defined above, is exhaustively described by these five variables. The variables are causatively independent of each other, but synergism can exist. For example, fibers of higher material moduli or larger diameter can enhance the structure stabilization by surface interaction as well, because they are able to support higher normal forces. This, in turn, results in greater frictional iramobilization. According to the above given interpretation of hair body, none of the five variables have exclusive influence on the overall behavior. Therefore, any specified level of body, if a quantitative scale existed, could be obtained by a nearly infinite number of variations among the five factors. Obviously, when a given bo.dy level is achieved by different combinations of the fundamental parameters-for instance, a decreasing fiber diameter is balanced by increas- ing hair density-some other perceptible hair mass characteristics will change. These changes, however, belong to second-order behavior patterns, specifical- ly to texture qualities. C. Cosmetic Products and Hair Body The specific influence of cosmetics on hair body is best discussed by analyzing the changes in the five basic parameters caused by different cosmetic products. It may be stated summarily that cosmetics-according to the current defini- tion of the term-cannot directly influence any of the five parameters so far as the biological synthesis of the fibers is concerned. Compositions or treat- ments which could grow denser, stronger, thicker, curlier, or rougher hair would be outside the field of cosmetics. Therefore, the discussion needs to involve only those effects of cosmetics which occur on grown hair. Cosmetic products can have only indirect and/or negative effects on fiber density. The on-head fiber number can be considered as a kinetic equilibrium determined by the rate of new fiber growth on the one hand and the rate of fiber elimination on the other. As mentioned above, fiber growth rate is not a cosmetically solvable problem. The rate of fiber attriti.on, however, can be influenced to some degree. Treatments or products, which result in more difficult combing, accelerate the rate of fiber elimination, thereby reducing the fiber density to a lower steady-state level. Lubricants, on the other hand, de- lay the mechanical fiber removal and assist in the maintenance of marginally higher fiber densities. Nonetheless, these effects are secondary, and it may be stated that cosmetics do. not significantly influence hair body through modi- fication of the fiber density on the scalp. The modulus or stiffness of polymeric materials can be increased by chemi- cal treatments. This has been achieved on natural fibers, including keratin fibers, by cross-linking, or by introducing bulky side groups. However, the nature of the reactants and/or the reaction conditions are such that, at pres- ent, these methods cannot be used for on-head treatments. No current cos- metic products increase body by this method. Conversely, some cosmetic
576 JOURNAL OF THE SOCIETY OF COSMETIC CItEMISTS products decrease the level of cystinc cross-links in hair. These include bleaches and especially bleaches followed by permanent waving. Their in- fluence on the dry modulus-and on whatever segment of body is derived from the modulus-is negligible, because the cystinc cross-links are not im- portant load bearing elements in dry fibers within the Hookcan range The toodull of the fibers can be influenced by internal or external deposi- tion of nonreactive materials as well. The resulting systems are composite structures with increased final fiber volumes, therefore, these will be discussed in connection with the fiber diameter effects. A specific case of modulus change occurs when the hair is swollen by liquids which interfere with the internal salt and/or hydrogen bonds of the fibers themselves. Wetting of intact hair by water decreases the modulus by nearly an order of magnitude. The wet modulus of an oxidatively modified hair is even lower. While the modulus reducing effect of fiber swelling liquids must be kept in mind when hair compositions are formulated, the fact in itself is of little importance for the present purpose. Hair body refers primar- ily to the dry and not to the wet state of the hair. The overly high softness of extensively bleached or bleached-waved wet hair may present problems dur- ing a shampoo and wet comb-out, but it does not translate to the dry be- havior. Overall, it may be concluded that present day cosmetic products and processes can influence hair body only marginally through modulus modi- fication. Body modification through fiber diameter increase can be accomplished by internal or external deposition of foreign materials. High levels of internal polymer deposition have been accomplished both on wool and cut hair, with significant increases in body type characteristics. While processes are avail- able for the deposition of solids, mostly polymeric materials, they are not presently utilized in cosmetic products for reasons already mentioned. On the other hand, materials of small molecular weight which are sorbed by the hair -such as alcohols, amines, etc.-most often act as plasticizers, therefore, de- feat the original purpose of increasing body. Only solid materials need to be considered for external deposition which can act as load bearing elements. While setting lotions and gels meet this re- quirement, the approach has serious limitations. The coating thickness must be very limited, if the natural fiber surface and topography are to. be main- tained. Consequently, hair body can be increased by surface deposition only if the coating is continuous and its stiffness is significantly higher than that of the fibers. In this case, the composite material-keratin core and external coating-has high bending stiffness. A specific case is when the solid deposit acts as an adhesive on heavily surface damaged fibrillated fibers. Through adhesively joining these splintered surface units to the main fiber body, they recover their load bearing ability in fiber deformation.
Previous Page Next Page